Pink Mule S.L.
email icon




Price: DKR 360.54 DKR 204.55
Ex Tax: DKR 163.64
Brand: Evolv
Product Code: 14004W
Availability: In Stock


2 X EFEST IMR 18500 - 1100mAh - 10A -  V.2 BATTERIES WITH NIPPLE 2 X EFEST IMR 18500 - 1100mAh - 10A - V.2 BATTERIES WITH NIPPLE DKR 82.64 Qty:
2 X EFEST IMR 18500 - 1100mAh - 10A - BATTERIES WITHOUT NIPPLE V.1 2 X EFEST IMR 18500 - 1100mAh - 10A - BATTERIES WITHOUT NIPPLE V.1 DKR 82.64 Qty:
Overall accessories:
Total product with accessories:
DKR 204.55
    - OR -   Add to Wish List
Add to Compare


The Kick  for those of you that like to have the option to use adjustable wattage control with your mechanical devices.

THE KICK  from EVOLV is the newest and most advanced item for your mechanical MOD.

THE KICK  is a small "drop-in" module that allows you to adjust the output wattage of your, otherwise non-variable, MOD.

This will avoid the disadvantage of using non-variable voltage, namely that your vape experience declines as the battery is discharged.

With THE KICK  you will obtain the widget on top of your battery that gives you the exact vape with the throat scratchy feeling and an optimum usage of the mizer that you want … during the battery's entire “life”.


THE KICK  automatically regulates the settings that suits your current mizer .. and considering the wattage you have predetermined it is the one that fits you best.

So you do not need to refresh your school learnings about Ohm law when using THE KICK.

It regulates your wattage and not your voltage.

THE KICK is placed on top of your battery providing it, at the same time, with optimum protection.

You can apply it to all MOD's that normally use 18650 batteries using 18500 batteries instead. It provides equal space to THE KICK on top of the battery.

THE KICK  is designed to be used in equipments with 18650 batteries before holding 18500 IMR Hight Drain batteries because there must also be room for the kick.

It allows you to adjust wattage and consequently how much heat your mizer produces.


There is a 90 day guarantee on The Kick, but it is personal. This means that you will need an order confirmation in order to use the warranty.

You can not get The Kick to work before you have assembled a mizer.

  1. ***USE IMR BATTERIES ONLY*** The Kick was designed to be used with IMR batteries only.
  1. DO NOT REMOVE THE CLEAR SHRINK-WRAP: It acts as a protective second layer of insulation against shorts.
  2. INSTALLING KICK MODULE: The Kick MUST be installed correctly. The bottom of the Kick must sit directly on the positive terminal of the battery (button end for button-top batteries). The top of the Kick (the end with the blue adjustment box) must be oriented towards the head of the device (never towards a device spring). The Kick is designed to be used in 18650 metal tube mods with an IMR 18490 or 18500 battery. Several device manufacturers are considering building extensions or longer tubes to permit the Kick to be used with the larger 18650 IMR batteries. The Kick may also be used with 18500 metal tube mods with an IMR 18350 battery.
  3. GROUND SPRING: You will notice a small spring attached to the top (side edge) of the Kick. This has been carefully designed and is an ESSENTIAL component of the Kick for proper functioning. The spring MUST make contact with the grounded inner wall of the battery tube. If this spring does not make contact, the Kick will not function. SOME (few) DEVICES HAVE ANODIZED or POWDER COAT ON THE INSIDE OF THE BATTERY Compartment. This can interfere with the ground connection. These coatings must be removed at the point of contact with the ground spring. 
    NOTE: DEVICE TUBES VARY - The internal diameter is wider on some and narrower on others. Please do not use the Kick in tube mods with an internal diameter greater than 19.5mm.
  4. Setting your Power Level (watts setting): The adjustment potentiometer (blue box) is located on the top side of the Kick. In the center of the box is a white adjustment screw to be used for adjusting the Kick's power setting. The watts settings are marked ON THE CIRCUIT BOARD and can be seen around the pot/blue-box. NOTE: there are lines underneath each setting number, follow the lines to the corresponding watts setting. Turning the adjustment screw clockwise increases power and counter-clockwise decreases power. The settings range is from 5 watts to 10 watts. The Kick performs best with attys/cartos rated between 1.3 to 3.0 Ohms. You can use higher rated resistance but the Kick will not regulate well at the highest power levels if resistance is above 3 ohms. Unlike Variable voltage devices, the Kick does not need frequent adjustments.Once you find your preferred Power level, there is no need to constantly adjust it because the Kick will maintain that Power level even if you change attys/cartos and/or resistance. You can use an under-load digital meter to see the volts as you change resistances and/or settings. AN ATOMIZER OR CARTOMIZER MUST BE ATTACHED TO THE METER OR YOU WILL NOT GET ANY READING.
  5. Low Battery Indicator: The Kick will detect, and stop functioning, when a battery charge level drops below 3.2 volts UNDER LOAD (with an atty/carto attached). This is a safety feature. The Kick will tell you this feature is activating when you experience STUTTER VAPE (vapor-no vapor alternating - may feel like tss-tss-tss). If you continue to vape beyond this indicator, the Kick will stop functioning until a fresh battery charge is detected. If you remove the battery and meter test it (unloaded) it may read between 3.4 and 3.6 volts. There are many variables that can contribute to the various unloaded readings.
  6. Battery life per charge: Many variables contribute to battery life per charge cycle. The Kick incorporates a boost circuit which requires more of your battery. Aggregate button/activation time, power setting, and atty/carto selection all factor into this equation. Battery age and conductive efficiency of the different devices are also variables. Using the Kick will reduce battery life per charge cycle. There is no way to provide use time per charge cycle as there are too many variables. On average, testers experienced reductions ranging from 10 to 20% depending on many different use variables.
  7. Short Circuit Protection: The Kick will detect shorts in the connection between the Kick and the atty/carto coil. This sensor is sensitive and if it detects short, the Kick will not fire. If you experience this, unthread your atty/carto and clean out any accumulated juice in all connections and then gently re-thread atty/carto until only finger-tip snug. If device still will not fire, try a different atty/carto and/or adapter. This is designed both as a safety feature and to protect the components of the Kick module.
  8. Battery safety: Please read the information on ECF and your battery supplier about recommended battery maintenance and overall battery safety in charging and using your batteries. Older batteries may not function as well as newer batteries. If a battery ever shows any sign of damage (torn or cracked outer surface, dents, or other), please discontinue all use of that battery and dispose of it in an approved battery recycling facility. Batteries should never be thrown into the trash - they should always be given to a recycling center that accepts batteries. 






Write a review

Your Name:

Your Review: Note: HTML is not translated!

Rating: Bad           Good

Enter the code in the box below:


Support: +34 9246520 75 / +349246520 72
Or we can call you. Please  write your telephone no:

(Remember your country code: 0047 xxxxx)

email icon



For you who wants to start waping...

We have compiled instructions, offers and more.

Read more

email icon

new to vape