USMODZ Stinger Squonk Akryl MOD (07)
  • USMODZ Stinger Squonk Akryl MOD (07)

USMODZ Stinger Squonk Acrylic MOD (07)

Price: DKK1,599.00
Tax included
Last items in stock

USMODZ Stinger Squonk Acrylic MOD (07)

Uses 1x20700/21700 (Battery not included)

Usmodz have made this beautiful mod called Stinger, it is a squonk mod packed with features due to the fantastic DNA75C Chip.

From the exclusive Acrylic design to the many muscles and the advanced features from the Evolv DNA75C chip, the Stinger Squonk mod has been created to thrill and impress any vaper.
No matter if you prefer a "normal but high quality vape" or advanced power vaping, this beauty will provide exactly what you need.

  • Evolv DNA75C Chip.
  • Variable Wattage from 1W - 75W.
  • Will run resistances from:
  • 0.08 Ohm - 1.0 Ohm in Temperature mode.
  • 0.10 Ohm - 2.0 Ohm in Wattage mode.
  • Uses one 20700 or 21700 battery. (minimum 25Amp -sold separately)
  • Upgradable Firmware and full control and adjustment of all features of the chip via the EScribe software.

The Usmodz Stinger squonk Mod is rather compact and the rounded shapes makes it a perfect fit for your hand.

The highly advanced Evolv DNA75C chip presents you with a world of opportunities - if you want them. The power comes from a single 20700 or 21700 or 21700 battery.


  • Made in beautiful Acrylic.
  • Chip: Evolv DNA75C.
  • Spring-loaded 510 connection.
  • 8.5ML Squonk bottle.
  • Adjust the power with Watt or Fahrenheit/Celsius "1Watt - 75Watt / 100° C - 315° C / 200° F - 600° F".
  • Will run resistances from:
  • 0.08 Ohm - 1.0 Ohm in Temperature mode.
  • 0.10 Ohm - 2.0 Ohm in Wattage mode.
  • The DNA75C chip can go lower but the built-in safety features will make sure you don't get an unsafe set up.
  • Temperature Control using Ni200, Titanium and Stainless Steel wire/coils.
  • Uses one 20700 or 21700 battery. (minimum 25Amp - sold separately)
  • Big TFT Color screen showing: Ohm, Volt/Watt/Temperature and battery level.
  • Micro USB port for upgrading the firmware.
  • It is not recommended to charge the battery through the USB port.
  • 5 Click on/off.
  • Short circuit protection.
  • Low Ohm protection.
  • Low Voltage protection.
  • Electronics overheat protection.
  • Size: 90mm x 58mm x 28mm.

Evolv DNA 75 Color features:

  • Output Wattage: 1 - 75 Watt in 0.1 Watt increments.
  • Output Voltage: 0.2 - 9 Volt.
  • Current out: 30 Amp. Max.
  • Atomizer resistance using Kanthal: Min. 0.1 Ohm, Average 0.25 Ohm, Max 2.0 Ohm.
  • Atomizer resistance using Ni200, Titanium and SS wire: Min. 0.08 Ohm, average 0.15 Ohm, Max 1.0 Ohm.
  • Lock the Ohm on your coil.
  • Temperature shown in Celsius or Fahrenheit.
  • Temperature limits: 100°C - 300°C (200°F - 600°F)
  • Big 160 x 80 pixel TFT colour screen.
  • Evolv DNA75 Color firmware can be updated via the Micro-USB port.
  • Download the EScribe software to get full control of the DNA75 Color chip.
  • Built in balancer for charging and monitoring each cell in the LiPo battery for a perfect charge.
  • 8 profiles that will allow you to make different settings for different tanks/atomizers.
  • High and Low Ohm protection.
  • E.g. if the Ohm is too low the chip will reduce the Wattage.
  • Short circuit protection.
  • Low resistance/ohm protection.
  • Overheating protection.
  • Built in safety on the print card.
  • Pre-heating of nickel wire.

Usmodz Stinger:

Usmodz have made the Stinger in beautiful Acrylic, this makes every mod a one in a kind. The 510 connector is made from Stainless Steel and have a self-adjusting pin, this makes a secure connection from mod to tank when squonking.

Stinger have nice rounded edges that makes it a pleasure to hold in the hand, buttons and bottle placement makes it a pleasure to use as everything is in perfect placements.

Battery etc.:

The Usmodz Stinger uses a single flat top 20700 or 21700 battery with a minimum of 25Amp.

To inset or replace the battery you need to remove the side panel, put the battery inside and place the panel back.
Inside the Stinger you also find the 8.5ML squonk bottle just beside the battery. Remember when filling the bottle never fill it to the top as there need to be room for the tube inside the bottle.

It is not recommended that you charge the battery inside the Stinger, use an external charger to ensure a perfect charge.

The amazing DNA75C Chip:

75W under the hood will leave you full of options, which is what the Stinger is all about.

It is also a Temp. Controlled Mod that will let you choose whatever wire you want to use in your coil. In Temp mode you can choose between Nickel, Titanium or Stainless Steel-wire. (the normal choice for TC vaping. Also, via the EScribe software, you can adjust the DNA75C chip to use any type of wire you desire)

Basically the DNA75C chip gives you control over any setting you could ever dream of. By using the EScribe software you can fine tune everything to your heart’s desire.
More than this, you can analyse any data in relation to your vaping thus letting you observe/analyse your vape down to the smallest puff.

Upgradable Firmware:

What is hot today might not be so tomorrow, therefore Evolv allows you to upgrade the firmware of the DNA chip (via the Micro-USB port and the EScribe software) so you can keep updated with all the latest features and the best specs.


1 Item